labelslkp.blogg.se - Giga nas dongle firmware

Giga nas dongle firmware how to#
Giga nas dongle firmware .exe#
Giga nas dongle firmware install#
Giga nas dongle firmware zip file#
Giga nas dongle firmware update#

Please let me know what I need to do to accomplish this. I just want EDEX4 to function as a 24/7 max reliability hard drive. Since I don’t use the features media streaming, dlna etc. This is wasting time, resources, and valuable disk space, and making my job of comparing the file size on the source and target to ensure proper file transfer very difficult since there are always extra files and folders! I don’t want any files automatically added to my shares on WDEX4. WDEX4 is still indexing my files and creating hidden folders. I am using fastcopy 2.11 and like windows explorer it yields a sustained rate of 10MB/sec with added reliability since it will log any failed transfers.Įventhough I have all the media streaming options turned off (under media tab and on my shares), and the latest firmware where this is supposed to be fixed. Keeping in mind the setup described above, which option would your engineers recommend for best performance?ģ.For initial loading of data onto the WDEX4 which software do you recommend for optimal speed? Besides windows explorer. I currently have it set to Active Backup. Since I have WDEX4 hooked up to the gigabit switch using both the primary and secondary gigabit ethernet ports, I have enabled the (Link Aggregation) option however surprisingly, your documentation does not even offer a description about what what each link aggregation option means and the best circumstances to use each one. Is it supported to connect WDEX4 to my desktop directly via usb3.0? If so how do I do it? Can I or must I use both USB ports? Keeping in mind USB 3.0 speed is 60MB/s which would be perfect if wdex4 can actually achieve it. Unfortunately the manual only references using usb to connect other hard drives, nothing about using USB for file transfer from a desktop directly. connect 1 port or both) so that the file transfers are done via dual usb 3.0.

Giga nas dongle firmware how to#

I have looked up the word usb in your full user manual to determine if it is possible to connect wdex4 to my desktop directly via usb and how to go about this (i.e. This is quite useless, I need to have at least 50MB/s for this NAS to be usable. This is when transferring files from my desktop to WDEX4. It starts of at 15-20 then quickly in 30 seconds or so goes down to 10.

While Gigabit Ethernet has a maximum of 125MB/s yet under the non-optimal setup described above, I am only getting a disappointing sustained rate of 10MB/s.

Gigabit switch1 -> Windows 7 Desktop (using gigabit network adapter) Gigabit router port -> Gigabit switch1 -> WDEX4 (connected using ethernet ports 1 & 2) (Most routers have only 4 ports anyway so it is an unreasonable requirement). Please do not suggest connecting to the router directly since that just isn’t possible. I am unable to connect WDEX4 directly to the router. Unfortunately due to infrastructure reqs. I am running wdex4 NAS with latest firmware (1.05.30) and with 4 WD Red 6TB drives within configured using RAID10 for a total redundant storage of about 12TB. The new version should be displayed in the lower right corner.Below is the case request I sent to WD support, I am posting it on the community in case someone here can help.

To verify the new firmware version, check NASNavigator again.

Once the unit reboots the following message should appear.

The updater will go through several steps and then reboot the unit.

Note that this screen shows the current and new versions of the firmware.

Enter the admin password for the unit and click OK.

Select the unit to be updated from the drop-down menu and click Update.

If so, click Run to continue with the firmware update.

Windows may give you a security warning.

Giga nas dongle firmware .exe#

exe file extension depending on your computer settings.

Otherwise the procedure is exactly the same. Note: For LinkStation units the filename will be 'LSUpdater.exe'.

Go down through the folders until you locate the file 'TSUpdater.exe'.

Once unzipped you should see the original file along with a folder by the same name.

Giga nas dongle firmware zip file#

Once the download finishes, right-click the zip file and choose 'Extract All' or use your preferred utility to un-zip the file.

Giga nas dongle firmware update#

Scroll to the firmware section and select the firmware update utility for Windows.

Go to the Buffalo website downloads page and enter your model number.

Giga nas dongle firmware install#

If NAS Navigator is not installed, download and install the application by clicking here. If the current IP is unknown the unit can be located using NAS Navigator. Access Settings, the TeraStation's web user interface, by entering the current IP address of the unit into a web browser.Updating the Firmware on a TeraStation or Linkstation from a Windows PC Search by either entering keywords or by selecting a product.